spec no: dsal3679 rev no: v.7 date: aug/20/2015 page: 1 of 5 approved: wynec checked: allen liu drawn: m.liu erp: 1203000588 3.0mmx1.0mm right angle phototransistor part number: APA3010P3BT-GX features z 3.0mmx2.0mmx1.0mm right angle smd led, 1.0mm thickness. z mechanically and spectrally matc hed to the infrared emitting led lamp. z package : 2000pcs / reel. z moisture sensitivity level : level 3. z tinned pads for improved solderability. z rohs compliant. description made with npn silicon phototransistor chips. package dimensions notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.15(0.006") unless otherwise noted. 3. the specifications, characteristics and technical data descri bed in the datasheet are subject to change without prior notice . 4.the device has a single mounting surface. the device must be mounted according to the specifications.
spec no: dsal3679 rev no: v.7 date: aug/20/2015 page: 2 of 5 approved: wynec checked: allen liu drawn: m.liu erp: 1203000588 electrical / optical characteristics at ta=25c absolute maximum ratings at ta=25c symbol parameter min. typ. max. units test conditions v br ceo collector-to-emitter breakdown voltage 30 v i c =100ua ee=0mw/c O v br eco emitter-to-collector breakdown voltage 5 v i e =100ua ee=0mw/c O v ce (sat) collector-to-emitter saturation voltage 0.8 v i c =2ma ee=20mw/c O i ceo collector dark current 100 na v ce =10v ee=0mw/c O t r rise time (10 to 90 ) 15 us v ce = 5v i c =1ma r l =1000 ? t f fall time (90 to 10 ) 15 us i (on) on state collector current 0.1 0.3 ma v ce = 5v ee=1mw/c O =940nm parameter max.ratings collector-to-emitter voltage 30v emitter-to-collector voltage 5v power dissipation at (or below) 25c free air temperature 100mw operating temperature -40c to +85c storage temperature -40c to +85c APA3010P3BT-GX
spec no: dsal3679 rev no: v.7 date: aug/20/2015 page: 3 of 5 approved: wynec checked: allen liu drawn: m.liu erp: 1203000588
spec no: dsal3679 rev no: v.7 date: aug/20/2015 page: 4 of 5 approved: wynec checked: allen liu drawn: m.liu erp: 1203000588 APA3010P3BT-GX recommended soldering pattern (units : mm; tolerance: 0.1) tape specifications (units : mm) reflow soldering is recommended and the soldering profile is shown below. other soldering methods are not recommended as they might cause damage to the product. reel dimension
spec no: dsal3679 rev no: v.7 date: aug/20/2015 page: 5 of 5 approved: wynec checked: allen liu drawn: m.liu erp: 1203000588 packing & label specifications APA3010P3BT-GX terms and conditions for the usage of this document 1. the information included in this docum ent reflects representative usage scenarios and is intended for technical reference on ly. 2. the part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. before production usage customer should refer to the latest datasheet for the updated specifications. 3. when using the products referenced in this document, please make sure the produc t is being operated within the environmental and electrical limits specified in the dat asheet. if customer usage exceeds the spec ified limits, kingbright will not be respon sible for any subsequent issues. 4. the information in this document applies to typical usage in consumer electronics applicati ons. if customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or m edical usage, please consult with kingbright representative for further assistance. 5. the contents and information of this document may not be reproduced or re-transmitted without permission by kingbright. 6. all design applications should refer to kingbright application notes available at http://www.kingbrightusa.com/applicationnotes
|
